2026-04-24 FE Backup
This commit is contained in:
@@ -0,0 +1,918 @@
|
||||
{
|
||||
"custom": {
|
||||
"FLT_Codes": [
|
||||
"0: No Fault",
|
||||
"1: Low Ambient Temperature",
|
||||
"2: High Ambient Temperature",
|
||||
"3: Low Chilled Liquid Temperature",
|
||||
"4: VSD Initialization Failure",
|
||||
"5: Low RTC Battery Voltage",
|
||||
"6: Invalid Number of Compressors Selected",
|
||||
"7: VSD Communications Failure",
|
||||
"8: Pre-charge Low DC Bus Voltage",
|
||||
"9: Pre-charge DC Bus Voltage Imbalance",
|
||||
"10: High DC Bus Voltage",
|
||||
"11: Low DC Bus Voltage",
|
||||
"12: DC Bus Voltage Imbalance",
|
||||
"13: High VSD Ambien Temperature",
|
||||
"14: Single Phase Input",
|
||||
"15: VSD Power Supply Fault",
|
||||
"16: VSD Logic Board Fault",
|
||||
"17: Motor Current Overload (Hardware)",
|
||||
"18: CT Plug Fault",
|
||||
"19: High Harmonic Filter Temperature",
|
||||
"20: Evap Anti-Freeze Pump Fault",
|
||||
"21: Low Heat Exchange Temperature",
|
||||
"22: Replace RTC Battery",
|
||||
"23: N/A",
|
||||
"24: N/A",
|
||||
"25: N/A",
|
||||
"26: N/A",
|
||||
"27: High Discharge Pressure",
|
||||
"28: High Differential Oil Pressure",
|
||||
"29: Low Differential Oil Pressure",
|
||||
"30: Low Suction Pressure",
|
||||
"31: High Discharge Temperature",
|
||||
"32: N/A",
|
||||
"33: Eductor Clog Fault",
|
||||
"34: Sensor Failure",
|
||||
"35: Low Motor Current",
|
||||
"36: High Motor Temperature",
|
||||
"37: Pre-charge Low DC Bus Voltage Immbalance",
|
||||
"38: Pre-charge DC Bus Voltage Imbalance",
|
||||
"39: High DC Bus Voltage",
|
||||
"40: Low DC Bus Voltage",
|
||||
"41: DC Bus Voltage Imbalance",
|
||||
"42: High Motor Current",
|
||||
"43: Motor Current Overload",
|
||||
"44: IGBT Gate Driver Fault",
|
||||
"45: High Baseplate Temperature",
|
||||
"46: Single Phase Input",
|
||||
"47: VSD Run Signal Fault",
|
||||
"48: High Discharge Press (HPCO)",
|
||||
"49: Low Suction Superheat",
|
||||
"50: Control Valve Fault",
|
||||
"51: Low Discharge Superheat",
|
||||
"52: Low Suction PRessure Smart Freeze",
|
||||
"53: Isolation Valve Failed to Close Warning",
|
||||
"54: Isolation Valve failed to Open Fault",
|
||||
"55: High Discharge Pressure Rate",
|
||||
"56: Condenser Fan VSD Fault Warning",
|
||||
"57: N/A",
|
||||
"58: N/A",
|
||||
"59: N/A",
|
||||
"60: N/A",
|
||||
"61: N/A",
|
||||
"62: N/A"
|
||||
],
|
||||
"OP_Codes": [
|
||||
"0: No code",
|
||||
"1: No code",
|
||||
"2: No code",
|
||||
"3: No code",
|
||||
"4: No code",
|
||||
"5: No code",
|
||||
"6: No code",
|
||||
"7: No code",
|
||||
"8: No code",
|
||||
"9: No code",
|
||||
"10: No code",
|
||||
"11: No code",
|
||||
"12: No code",
|
||||
"13: No code",
|
||||
"14: 1No code",
|
||||
"15: No code",
|
||||
"16: No code",
|
||||
"17: No code",
|
||||
"18: No code",
|
||||
"19: No code",
|
||||
"20: No code",
|
||||
"21: No code",
|
||||
"22: No code",
|
||||
"23: No code",
|
||||
"24: No code",
|
||||
"25: No code",
|
||||
"26: No code",
|
||||
"27: No code",
|
||||
"28: No code",
|
||||
"29: No code",
|
||||
"30: No code",
|
||||
"31: No code",
|
||||
"32: No code",
|
||||
"33: No code",
|
||||
"34: No code",
|
||||
"35: No code",
|
||||
"36: No code",
|
||||
"37: No code",
|
||||
"38: No code",
|
||||
"39: No code",
|
||||
"40: No code",
|
||||
"41: No code",
|
||||
"42: No code",
|
||||
"43: No code",
|
||||
"44: No code",
|
||||
"45: No code",
|
||||
"46: No code",
|
||||
"47: No code",
|
||||
"48: No code",
|
||||
"49: No code",
|
||||
"50: No code",
|
||||
"51: No code",
|
||||
"52: No code",
|
||||
"53: No code",
|
||||
"54: No code",
|
||||
"55: No code",
|
||||
"56: No code",
|
||||
"57: No code",
|
||||
"58: No code",
|
||||
"59: No code",
|
||||
"60: No code",
|
||||
"61: No code",
|
||||
"62: No code",
|
||||
"63: Manual Override",
|
||||
"64: Daily Schedule Shutdown",
|
||||
"65: Unit Switch Off",
|
||||
"66: Remote Controlled Shutdown",
|
||||
"67: Loss of External Communications",
|
||||
"68: Flow Switch Shutdown",
|
||||
"69: VSD Cooling Shutdown",
|
||||
"70: Serial Number Shutdown",
|
||||
"71: N/A",
|
||||
"72: Discharge Spuerheat Recovery",
|
||||
"73: N/A",
|
||||
"74: No Run Permissive",
|
||||
"75: Anti-Recycle Timer Active",
|
||||
"76: System Switch Off",
|
||||
"77: System Not Running",
|
||||
"78: System Running",
|
||||
"79: Discharge Pressure Limiting",
|
||||
"80: Suction Pressure Limiting",
|
||||
"81: Motor Current Limiting",
|
||||
"82: Free Cooliong",
|
||||
"83:BAS Motor Current Limiting",
|
||||
"84: Remote Motor Current Limiting",
|
||||
"85: System Pumping Down",
|
||||
"86: VSD Pre-Charging",
|
||||
"87: VSD Baseplate Temp Limiting",
|
||||
"88: VSD Internal Ambient Temp Limiting",
|
||||
"89: Sounf Limiting",
|
||||
"90: BAS Sounf Limiting",
|
||||
"91: Remote Sound Limiting",
|
||||
"92: Pulldown Motor Current Limiting",
|
||||
"93: Cooling Demand Shutdown",
|
||||
"94: Input Current Limiting",
|
||||
"95: BAS Input Current Limiting",
|
||||
"96: Remote Input Current Limiting",
|
||||
"97: Pulldown Input Current Limiting"
|
||||
],
|
||||
"allTags": [
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 20,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Comm Interface Percentage",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 43,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 1 Economizer Percent",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 44,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 2 Economizer Percent",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 51,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Condenser 1 Fan Speed",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 52,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Condenser 2 Fan Speed",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 29,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "FLA Motor 1 Percent",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 30,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "FLA Motor 2 Percent",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 5,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Load",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 31,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 1 Power",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 32,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 2 Power",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 27,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 1 Fan Power",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 28,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 2 Fan Power",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 17,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "VSD CMD",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 19,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "VSD Output",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 15,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Ambient Air Temperature",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 37,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 1 Eductor Temperature",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 39,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 1 Motor Temperature",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 38,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 2 Eductor Temperature",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 40,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 2 Motor Temperature",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 53,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Condenser 1 Temperature",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 54,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Condenser 2 Temperature",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 16,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Evaporator In Water Temperature",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 18,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Evaporator Out Water Temperature",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 22,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 2 Discharge Temperature",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 6,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Flow",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 45,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 1 Runtime",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 46,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 2 Runtime",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 7,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Active Setpoint",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Boolean",
|
||||
"displaySelection": 1,
|
||||
"format": "0.0",
|
||||
"instancePosition": 10,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Chiller System Available",
|
||||
"options": [
|
||||
"Not ready",
|
||||
"Ready"
|
||||
]
|
||||
},
|
||||
{
|
||||
"dataType": "Int4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 47,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 1 Starts",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Boolean",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 33,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 1 Status",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Int4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 48,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 2 Starts",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Boolean",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 34,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 2 Status",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Boolean",
|
||||
"displaySelection": 1,
|
||||
"format": "0.0",
|
||||
"instancePosition": 49,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Condenser 1 Fan Status",
|
||||
"options": [
|
||||
"Off",
|
||||
"On"
|
||||
]
|
||||
},
|
||||
{
|
||||
"dataType": "Boolean",
|
||||
"displaySelection": 1,
|
||||
"format": "0.0",
|
||||
"instancePosition": 50,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Condenser 2 Fan Status",
|
||||
"options": [
|
||||
"Off",
|
||||
"On"
|
||||
]
|
||||
},
|
||||
{
|
||||
"dataType": "Boolean",
|
||||
"displaySelection": 1,
|
||||
"format": "0.0",
|
||||
"instancePosition": 12,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Evaporator Heater Status",
|
||||
"options": [
|
||||
"Off",
|
||||
"On"
|
||||
]
|
||||
},
|
||||
{
|
||||
"dataType": "Boolean",
|
||||
"displaySelection": 1,
|
||||
"format": 0,
|
||||
"instancePosition": 14,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Evaporator Pump Status",
|
||||
"options": [
|
||||
"Off",
|
||||
"On"
|
||||
]
|
||||
},
|
||||
{
|
||||
"dataType": "Boolean",
|
||||
"displaySelection": 1,
|
||||
"format": 0,
|
||||
"instancePosition": 8,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Flow Switch",
|
||||
"options": [
|
||||
"Off",
|
||||
"On"
|
||||
]
|
||||
},
|
||||
{
|
||||
"dataType": "Int4",
|
||||
"displaySelection": 1,
|
||||
"format": "0.0",
|
||||
"instancePosition": -3,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 1 OpCode"
|
||||
},
|
||||
{
|
||||
"dataType": "Int4",
|
||||
"displaySelection": 1,
|
||||
"format": 0,
|
||||
"instancePosition": 0,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 1 Fault Code"
|
||||
},
|
||||
{
|
||||
"dataType": "Int4",
|
||||
"displaySelection": 1,
|
||||
"format": 0,
|
||||
"instancePosition": 1,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 2 Fault Code"
|
||||
},
|
||||
{
|
||||
"dataType": "Int4",
|
||||
"displaySelection": 1,
|
||||
"format": 0,
|
||||
"instancePosition": -2,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 2 OpCode"
|
||||
},
|
||||
{
|
||||
"dataType": "Boolean",
|
||||
"displaySelection": 1,
|
||||
"format": "0.0",
|
||||
"instancePosition": 3,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System HOA",
|
||||
"options": [
|
||||
"Local",
|
||||
"Remote"
|
||||
]
|
||||
},
|
||||
{
|
||||
"dataType": "Boolean",
|
||||
"displaySelection": 1,
|
||||
"format": "0.0",
|
||||
"instancePosition": 9,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System Interlock Active",
|
||||
"options": [
|
||||
"Not Tripped",
|
||||
"Tripped"
|
||||
]
|
||||
},
|
||||
{
|
||||
"dataType": "Boolean",
|
||||
"displaySelection": 1,
|
||||
"format": "0.0",
|
||||
"instancePosition": 11,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System Permissive OK",
|
||||
"options": [
|
||||
"Not Ready",
|
||||
"Ready"
|
||||
]
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 41,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 1 Oil Pressure",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 42,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "Compressor 2 Oil Pressure",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 23,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 1 Discharge Pressure",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 21,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 1 Discharge Temperature",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 25,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 1 Suction Pressure",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 24,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 2 Discharge Pressure",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 26,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 2 Suction Pressure",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 13,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System Suction Cutout",
|
||||
"options": []
|
||||
},
|
||||
{
|
||||
"dataType": "Float4",
|
||||
"displaySelection": 0,
|
||||
"format": "0.0",
|
||||
"instancePosition": 20,
|
||||
"instanceStyle": {
|
||||
"classes": ""
|
||||
},
|
||||
"name": "System 1 Discharge Pressure",
|
||||
"options": [],
|
||||
"visible": false
|
||||
}
|
||||
]
|
||||
},
|
||||
"params": {
|
||||
"tagPath": "[Ignition_Common_IO_Gtwy]Roof/SATB1_RF_CH06_SYSTEM"
|
||||
},
|
||||
"propConfig": {
|
||||
"custom.FLT_Codes": {
|
||||
"persistent": true
|
||||
},
|
||||
"custom.OP_Codes": {
|
||||
"persistent": true
|
||||
},
|
||||
"custom.allTags": {
|
||||
"binding": {
|
||||
"config": {
|
||||
"struct": {
|
||||
"tagPath": "{view.params.tagPath}"
|
||||
},
|
||||
"waitOnAll": true
|
||||
},
|
||||
"enabled": false,
|
||||
"transforms": [
|
||||
{
|
||||
"code": "\toutput \u003d []\n\t# Simulate fetching tag configurations and sorting by name\n\tnodes \u003d system.tag.getConfiguration(value[\u0027tagPath\u0027], True)\n\tfor item in nodes:\n\t if \u0027tags\u0027 in item:\n\t \tsortedTags \u003d sorted(item[\u0027tags\u0027], key\u003dlambda x: x[\u0027name\u0027])\n\t \tsortedTags \u003d sorted(sortedTags, key\u003dlambda x: x.get(\u0027engUnit\u0027, \u0027misc\u0027) if x.get(\u0027engUnit\u0027, \u0027misc\u0027) !\u003d \"\" else \u0027misc\u0027)\n for tagConfig in sortedTags:\n if str(tagConfig[\u0027tagType\u0027]) \u003d\u003d \u0027AtomicTag\u0027:\n name \u003d tagConfig.get(\"name\", \"\")\n dataType \u003d tagConfig.get(\"dataType\", \"\")\n tagPath \u003d value[\u0027tagPath\u0027] + \u0027/\u0027 + name\n if dataType \u003d\u003d \u0027Boolean\u0027:\n \tdisplaySel \u003d 1\n else:\n \tdisplaySel \u003d 0\n instance \u003d {\n \"instanceStyle\": {\n \"classes\": \"\"\n },\n \"instancePosition\": 999,\n \"name\": name,\n \"dataType\": dataType,\n \"displaySelection\": displaySel,\n \"format\": \"0.0\",\n \"options\": []\n }\n output.append(instance)\n\t# Return or process the sorted output\n\treturn output",
|
||||
"type": "script"
|
||||
}
|
||||
],
|
||||
"type": "expr-struct"
|
||||
},
|
||||
"persistent": true
|
||||
},
|
||||
"custom.allTags[38].options": {
|
||||
"binding": {
|
||||
"config": {
|
||||
"path": "view.custom.OP_Codes"
|
||||
},
|
||||
"type": "property"
|
||||
}
|
||||
},
|
||||
"custom.allTags[39].options": {
|
||||
"binding": {
|
||||
"config": {
|
||||
"path": "view.custom.FLT_Codes"
|
||||
},
|
||||
"type": "property"
|
||||
}
|
||||
},
|
||||
"custom.allTags[40].options": {
|
||||
"binding": {
|
||||
"config": {
|
||||
"path": "view.custom.FLT_Codes"
|
||||
},
|
||||
"type": "property"
|
||||
}
|
||||
},
|
||||
"custom.allTags[41].options": {
|
||||
"binding": {
|
||||
"config": {
|
||||
"path": "view.custom.OP_Codes"
|
||||
},
|
||||
"type": "property"
|
||||
}
|
||||
},
|
||||
"params.tagPath": {
|
||||
"paramDirection": "input",
|
||||
"persistent": true
|
||||
}
|
||||
},
|
||||
"props": {},
|
||||
"root": {
|
||||
"children": [
|
||||
{
|
||||
"meta": {
|
||||
"name": "FlexRepeater"
|
||||
},
|
||||
"position": {
|
||||
"basis": "100%"
|
||||
},
|
||||
"propConfig": {
|
||||
"props.instances": {
|
||||
"binding": {
|
||||
"config": {
|
||||
"struct": {
|
||||
"allTags": "{view.custom.allTags}",
|
||||
"tagPath": "{view.params.tagPath}"
|
||||
},
|
||||
"waitOnAll": true
|
||||
},
|
||||
"transforms": [
|
||||
{
|
||||
"code": "\toutput \u003d []\n\tallTags \u003d system.util.jsonDecode(system.util.jsonEncode(value[\u0027allTags\u0027]))\n\tfor tag in allTags:\n\t\ttagName \u003d tag[\"name\"]\n\t\ttag[\"tagPath\"] \u003d value[\"tagPath\"] + \"/\" +tagName\n\t\toutput.append(tag)\n\toutput_sorted \u003d sorted(output, key\u003dlambda item: item[\"instancePosition\"])\n\treturn output_sorted",
|
||||
"type": "script"
|
||||
}
|
||||
],
|
||||
"type": "expr-struct"
|
||||
}
|
||||
}
|
||||
},
|
||||
"props": {
|
||||
"alignContent": "flex-start",
|
||||
"elementPosition": {
|
||||
"basis": "50%",
|
||||
"grow": 0
|
||||
},
|
||||
"loading": {
|
||||
"order": "with-parent"
|
||||
},
|
||||
"path": "Library/Framework/Tag Info",
|
||||
"style": {
|
||||
"border": "1px solid var(--border)",
|
||||
"gap": "10px 0",
|
||||
"padding": "10px"
|
||||
},
|
||||
"useDefaultViewHeight": false,
|
||||
"useDefaultViewWidth": false,
|
||||
"wrap": "wrap"
|
||||
},
|
||||
"type": "ia.display.flex-repeater"
|
||||
}
|
||||
],
|
||||
"meta": {
|
||||
"name": "root"
|
||||
},
|
||||
"props": {
|
||||
"direction": "column",
|
||||
"style": {
|
||||
"classes": "containers/padded-container"
|
||||
}
|
||||
},
|
||||
"type": "ia.container.flex"
|
||||
}
|
||||
}
|
||||
Reference in New Issue
Block a user