Parameters for PI_B function block Reserved for autotuning Lower limit of the process value range Upper limit of the process value range Lower limit of the output value range Upper limit of the output value range 0: direct action of the PID controller 1: opposite action of the PID controller 1: the RCPY input is used Proportional contribution (gain) Integral time Dead zone on deviation Manual adjustment of static deviation Analog input value Forced value Force command Forced state Physical value Function type Channel health Channel warning Measurement status word Aligned channel Measurement within lower tolerance zone Measurement within upper tolerance zone Internal offset error Internal reference error Power supply error SPI communication error Module health Module faults Module health Module faults Module health Module faults Analog output value Forced Value Force command Forced state Physical value Function type Channel health Module health Module faults Module health Module faults Module health Module faults Channel health Discrete input value Module health Module faults Module health Module faults Module health Module faults Module health Module faults Channel health Discrete output value Module health Module faults Module health Module faults Module health Module faults Module health Module faults Channel error Discrete input value Common array for communication EF Mid-Range Common array for EIO communication function blocks Common array for communication EF Datatype extended for master control block MSTR_CTL operation code error status number of data units transferred operation-dependent information routing address operation-dependent information Data structure for the XMIT configuration Data Rate Data bits Parity Stop bits Command word Message Length Retry limit Start of transmission delay (ms) End of transmission delay (ms) Response time-out (ms) Health bits of rack 0: slots 0 to 15 Health bits of rack 1: slots 0 to 15 Device name of the CRA drop Firmware version of the CRA Rotary switches value at power up State of the CRA module CRA diagnostic information At least one IO error in drop when 0 CCOTF in progress CCOTF error IOPL mismatch Rotary switches have changed since last power up Drop communication health Redundant power supply status Execution time of the last CRA cycle (unit: 0.01 ms) Longes CRA cycle execution time (unit: 0.01 ms) Shortest CRA cycle execution time (uint: 0.01 ms) Number of time stamp records available in the drop local buffer Diagnostic information about the source time stamped events service Time valid and synchronized Clock failure Clock not synchronized Buffer full Percentage of the buffer filled [0..100] Main state of the TS events service Ethernet status Link up/down for Ethernet port 1 Link up/down for Ethernet port 2 Link up/down for Ethernet port 3 Link up/down for Ethernet backplane port Ethernet/IP RPI change in progress Redundant owner is present 0: one or more services not operating normally / 1: all operational One bit for each user-observable feature 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled Ethernet backplane status (0: failure, 1: OK) Ethernet backplane error (0: error, 1: OK) Ethernet port status Time elapsed since last update from NTP server (unit: 100 ms) Max packet interval for output packets (unit: 1 ms) Number of bytes received on interface Numberof inbound packets that contain errors Number of bytes sent on interface Number of outbound packets that contain errors SOE uncertain (in timestamping system only) Ethernet status Link up/down for Ethernet port 1 Link up/down for Ethernet port 2 Link up/down for Ethernet port 3 Link up/down for Ethernet backplane port Scanner OK and scanning at least 1 equipment (if at least 1 equipment configured) 0: one or more services not operating normally / 1: all operational 1: No traffic overload detected / 0: Traffic overload detected One bit for each user-observable feature 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled Main IP address status (0 in caes of duplicate IP or no IP assigned) 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled 0: service not operating normally / 1: service operating normally or disabled One bit for each user-observable feature LLDP service status 0: event log service not operating normally / 1: event log service operating normally 1: No acknowledgement received from the syslog server / 0: otherwise Ethernet port 1 and 2 status Ethernet port 3 and backplane port status MSB=Major revision, LSB=Minor revision % of FDR server usage Number of packets received on interface Number of inbound packets that contain errors Number of packets sent on interface Number of outbound packets that contain errors Signature of all files on local module FDR server Local Slave health bits (local slave 1 to 16) DIO health bits (1 bit per DIO up to 128 DIOs. 112-127 are reserved for future extension) DIO control bits (1 bit per DIO up to 128 DIOs. 112-127 are reserved for future extension) Status of the remote PLC Applications of the primary and the standby are different from the origin Command that allows logic mismatch between the primary and the standby Applications of the primary and the standby are running with different step of online modification Applications of the primary and the standby are running with difference at least one SFC section Applications of the primary and the standby are running with different steps of offline modification Number of differences between the application of the primary and application of the secondary Number maximum of differences allowed between application of the primary and the application of the secondary Command that allows firmware mismatch between the primary and the standby Firmware of the primary is different from the firmware of the standby Data layout of the primary is different from the data layout of the standby Amount of data in KByte sent by the primary and discarded by the standby Amount of data in KByte not updated by the standby (rounded to the upper) Backup application of the primary and backup application fo the standby Command that allows PLC A to go promary or standby (modification allowed only on primary) Command that allows PLC B to go primary or standby (modification allowed only on primary) Swap primary and standby command (modification allowed only on primary) Transfer application from the primary to the standby command (modification allowed only on primary) Command that automatically start the application in Run after transfer (modification allowed only on primary) Run remote controller command (modification allowed only on primary) Stop remote controller command (modification allowed on primary, on stop or on wait) Command that start a comparison of the variable initial values (modification allowed only on primary) Initial values comparision status Exchanged data from the last MAST cycle standby receipt status Exchanged data from the last FAST cycle standby receipt status Exchanged data from the last SAFE cycle standby receipt status Hot standby link error (no heartbeat connection on hot standby link) Hot standby supplementary link error (no heartbeat connection on supplementary link) The PLC is in Run but is waiting to be part of the hot standby system The PLC is in Run Primary state The PLC is in Run Standby state The PLC is in Stop The PLC switch is on A position The PLC switch is on B position The PLC does not see any of the configured EIO drops An SD Card is inserted True: the local rack is OK / False: the local rack is not ok (module missing) Free space to exchange information between primary and standby PLCs.